![]() In addition to this, it is essential to select the charge current in accordance with the battery size. So, for a 12-Volt lead-acid battery containing six cells, you are required to set the voltage to 12V (6 x 2V). To give an example, the nominal voltage of lead-acid is 2 volts per cell. Then, set the desired voltage and current limit, which you need to charge the battery. All you need to do is to connect the battery to the adjustable power supply. Lead Acid Scooter Batteriesīefore charging a lead acid scooter battery, it is essential to calculate the exact voltage, determined by the number of cells in the battery. This is because once the battery is fully charged the process will not terminate automatically. This could result in overheating which can ultimately damage the battery’s internal cells, or, in rare cases, cause an explosion.Īs there are different types of batteries, including lead-acid, lithium-ion and the NiCd or NiMH, we will take a look at each one. However, charging a scooter battery with a power supply is not without risk, and it is important that the battery is not left unattended. Variable power supplies can be purchased online or at any specialist electrical store. This is a simple power supply which charges with an adjustable voltage feature, whilst limiting the current flow. This can be accomplished using a Variable Power Supply. Many of us don’t realise that scooter batteries can be charged manually. How to Charge a Scooter Battery without a Charger – Build Your own Battery Charger.Contact your scooter battery retailer for information on the correct replacement battery for your scooter. ![]() If the scooter fails to start again, you may need to buy one of our replacement scooter batteries. Run the scooter for an extended period to recharge the battery. Replace the battery compartment cover and secure it in place. This may damage the scooter battery and electrical system. Do not keep the cables connected for extended period because the car’s alternator releases too many amps. After the scooter has started, disconnect the jumper cables by removing the negative clamp first and then positive clamp. ![]() The car battery should have enough cranking power to start the scooter. You can reduce the potential of damage to your scooter by turning the car off. Attach the cables to the dead battery first. Use jumper cables to connect the negative terminals and then the positive terminals. If you do not have a battery pack, you can use a car to start your scooter. Best of all, they can also be used as a power bank to charge your phone, tablet, laptop, etc. The newer handheld lithium jump starters, such as the Weego JS6 and JS12, can easily be carried in your bag or purse or left on the scooter in one of the storage compartments. When the engine starts, disconnect the negative cable first and then remove the positive cable. Connect the negative terminals first and then the positive terminals. Ensure that the battery pack is set to 12-volts prior to connecting the cables to the scooter battery terminals. Red indicates that a terminal is positive, and black means that a terminal is negative. Identify the positive and negative terminals on the scooter battery and the jump pack. Remove the screws or pop open the quick disconnect clamps that secure the battery cover to access the battery compartment. You must lift or remove the seat to gain access to the battery if it is mounted near the fuel tank. If it is located beneath the footrest, lift the rubber mat to access the battery cover. ![]() Your owner’s manual will identify the location of the battery for your particular scooter. The battery may be mounted beneath the seat or below the footrest. Cover the scooter battery with an old towel after connecting the terminals to prevent contact with the acid. Battery acid can leak during the charging process. Park the vehicle a safe distance from open flames and all sources of heat. Protect your eyes with safety goggles, and wear work gloves to safeguard your hands. You will need to jump-start the battery if the usual procedure for starting the scooter fails.Įnsure that you take sufficient safety precautions while jump-starting the battery. If this occurs, the battery will not have the cranking amps required to start the gasoline engine. Although these batteries are designed to take and hold a charge on a regular basis, they can lose that capacity over time. These highly fuel-efficient vehicles have electric starting systems that are powered by a battery. Scooters are becoming more popular as a means of transportation for commuters, college students and for running short errands. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |